H/S/H With “Coil Split” Push Pull Mods Prewired Electronic Assembly for Stratocaster type guitars – Solderless

R699.00

In stock

Description

A high quality electronic replacement / upgrade for Stratocaster style guitars with 2 humbuckers and 1 single coil pickups with 2 push/pull tone pots for coil splitting the humbuckers.
The layout is a per Fender USA/MEX Standard strat. This will fit squier or other guitars but we can not guarantee the layout will be the same, the pots and switch need to be fixed to the plate, if you are unsure if this plate will fit onto your pickguard you can purchase one of our pickguards, all the pickguards we sell at Valley Sound for Strat will work.

Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometer for Volume and Push/Pull pots for tones. Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our solderless connector. We also have a prewired output jack with cloth wire for R99 as an optional extra. It is easy to do, the connector is spring activated so you just press on the orange part with a screwdriver, insert the wire and release. All the ground wires go to the bottom terminals and each hot goes to top terminals. They will be colour coded so you know where to put the hot of each component:

Output jack hot gets connected to the white terminal
Neck pickup to the blue terminal
Middle pickup to the red terminal
Bridge pickup to the yellow terminal

Coil split wire to top screw terminal of each tone pot marked with a yellow dot. Middle screw terminal on each tone pot offers an extra ground connection for pickups / bridge / body grounding. If you want your pickups to be coil split normally and full humbucker with you pull the knob up, then you would connect the coil split wires to the terminal without any dot.

 

Please note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. Please see how this will come wired standard, these can be customized to your preference. make your purchase then email us if you want any changes.

 

1st Tone pot assigned controll options:
– Neck pickup
– Both Neck and Middle pickups (Standard with this wiring assembly)

 

2nd Tone pot assigned controll options:
– Middle
– Both Middle and Bridge pickups
– Bridge Pickup (Standard with this wiring assembly)

Vintage Standard Fender Spec is Neck pickup on 1st Tone, Middle pickup on 2nd Tone and Bridge pickup without any tone control. Modern Fender and most other guitars have Neck and Middle on 1st Tone Pot and Bridge on 2nd Tone pot. Some players who like to use the middle pickup for funk tones like to have the middle pickup without any tone control and have neck on tone 1 and bridge on tone 2. We will do the standard modern wiring unless you specify otherwise in the order notes or email.

Switch tip colour options:
– Cream
– Black
– White (Standard if you do not inform us of a different colour choice)

Potentiometer knobs are not included, please purchase them separately should you require.

 

PLEASE NOTE: Thin bodied guitars with shallow routing (such as Squier Bullet and Affinity) may not accommodate push/pull pots, you need at least 30mm routing depth by the pots, check the area where your switch goes, you need 35mm routing depth in the cavity by the switch too as these switches are slightly larger than the cheaper ones.

 

Additional information

Dimensions 10 × 5 × 5 cm

Reviews

There are no reviews yet.

Be the first to review “H/S/H With “Coil Split” Push Pull Mods Prewired Electronic Assembly for Stratocaster type guitars – Solderless”

Your email address will not be published. Required fields are marked *



css.php